Engineering Science Research

Engineering Science Research Paper

Electric Power

Synthesis and Conducting Properties at Intermediate Temperature of BaCe1-xYxO3-α

It is well known that because high-temperature proton conductors have special proton-conducting function, they have valuable and potential applications in some electrochemical devices and membrane reactors such as fuel cells, gas sensors, hydrogenation and dehydrogenation of some organic compounds, ammonia synthesis at atmospheric pressure, steam electrolyzer, and separation and purification of hydrogen, etc.Y2O3 doped BaCeO3 [...]

, , , , ,

Research on Active Power Filter in Reactive Power Compensation and Harmonic Restraining

With the development of the electronic technology and the extensive apply of the power electronic device,Higher requirements about using and quality of power are put forward.Active Power filter(APF) is considered as the most effetive method to harness the serious “power pollution”.It is a developmental tendency of utilizing APF compensating harmonic current and idle-current.In order to [...]

, , ,

Preparation and Properties of Interconnect Materials for Solid Oxide Fuel Cells

Solid oxide fuel cells (SOFCs) are high efficiency and clean power system, which convert the chemical energy of the fuels directly to electrical energy. As an open circuit voltage of single cell at operation is approximately 1 V, the cells must be connected electrically in series with the help of an interconnect material to provide [...]

, , , , , ,

The Study and Design of 35W Metal Halide Lamp Digital Electronic Ballast

The Metal halide lamp (MHL), it is the important light source as a high-intensity gas discharge lamp, it has the most development potential of high-tech products and representative of industrial products that have advanced technical level in electrical light sources industry. The metal halide lamps have some characteristics with high luminous efficacy, long life and [...]

, , ,

Experimental Study of Dynamic Per-Formance of Small Passive Direct Methanol Fuel Cells

Fuel cells are the devices which continually convert the chemical energy of the fuel and oxidant into electrical energy through the electrochemical reaction directly. Because of their environmental compatibility and high efficiency, fuel cells have drawn increasing attention from governments and enterprises all over the world. Direct methanol fuel cells (DMFCs) have the advantages of [...]

, ,

The Reliability Analysis of Microwave Anechoic Chamber and Its Automatic Test Systems

Recently, with the increasing application of wireless communication, the test techniques of the RF terminal equipments such as the mobile phone are paid more attentions, which mainly include the test of gain, TRP (Total Radiated Power) and TIS (Total Isotropic Sensitivity). These test processes should be in the microwave anechoic chamber. So the characteristics of [...]

, , , ,

Derivation and Validation about Electrodynamic Force of Switchboard

The selection and settlement of busbar is very important in distribution panel R&D. In designing, especially for busbar Electric Power Force quantification calculating, we often estimate by our working experience or consult some national standards or IEC specifications and other relative technical documents, for there are so few information to refer. So I did the [...]

, , , ,

Study on the Reliability of Residual Current Protection of CM2L MCCB

Residual current circuit breaker(viz. moulded case circuit breaker with residual current protection) is a type of new low-voltage safe protection device, it can offer not only overload and short circuit protection but also avoid the electric shock and fire accident.The study on the reliability of residual current circuit breaker is very important for improving the [...]

, , , ,

Based on Virtual Prototyping Technology Mechanism Simulation of Circuit Break and Optimization Mechanism Spring

Low-voltage circuit breakers is an important member of low-voltage electrical apparatus, its performance mostly depend on performance of operating mechanism. Domestic designers mainly use graphical solution method, i.e. drawing the position of mechanism motion at every moment, to get motion characteristic of mechanism, which has many disadvantages such as inaccuracy. The application of virtual prototype [...]

, , , ,

Research on the Green Glamping Device System Driven by the Linear Motor

Abstract At present, the vast majority of the mobile fixtures using in the field of machinery manufacturing are the hydraulic or pneumatic transmission fixture. The energy transfer line of the two types of the fixtures will result in greater energy loss because they go through a number of links from the energy input to mechanical [...]

, , , ,

Previous Posts